BGA V1A10 E6327

BGAV1A10 B G AV 1 A 1 0 Lo w N o i s e A m p l i f i e r w i t h G a i n C o n t r o l Features • Operating frequencies: 3.4 - 3.8 GHz • Insertion power gain: 18.0 dB • Gain dynamic range: 22 dB • Low noise figure: 1.3 dB • Low current consumption: 5.0 mA • Multi-state control: Gain- and Bypass-Modes 1.1 x 1.5 mm2 • Small ATSLP leadless package Application The LTE data rate can be significantly improved by using the high gain LNA. The integrated gain control and bypass function increases the overall system dynamic range and leads to more flexibility in the front-end. In high gain mode the BGAV1A10 offers best Noise Figure to ensure high data rates even on the LTE cell edge. Closer to the basestation the bypass mode can be activated reducing current consumption. Thanks to the MIPI control interface, control lines are reduced to a minimum. Product Validation Qualified for industrial applications according to the relevant tests of JEDEC47/20/22. Block diagram S S RFin RFout LNA VIO VDD Data Sheet www.infineon.com MIPI-RFFE Control1Interface SDATA SCLK USID1 USID2 Revision 3.0 2018-04-23 BGAV1A10 Low Noise Amplifier with Gain Control Table of Contents Table of Contents Table of Contents 1 1 Maximum Ratings 2 2 DC Characteristics 3 3 RF Characteristics - Band 42 3 4 RF Characteristics - Band 43 5 5 MIPI RFFE Specification 8 6 Application Information 12 7 Package Information 14 Data Sheet 1 Revision 3.0 2018-04-23 BGAV1A10 Low Noise Amplifier with Gain Control Maximum Ratings 1 Maximum Ratings Table 1: Maximum Ratings Parameter Symbol Values Min. Typ. Max. Unit Note / Test Condition Supply Voltage VDD V DD -0.3 – 2.5 V 1 Voltage at RFin V RFI -1 – 1 V – Voltage at RFout V RFO -1 – 1 V – Current into pin VDD IDD -30 – – mA – – RF input power PIN – – 25 dBm Total power dissipation Ptot – – 90 mW Junction temperature TJ – – 150 ◦ C – TA -30 – 85 ◦ C – Storage temperature range T STG -55 – 150 ◦ C – ESD capability, HBM V ESD_HBM -1000 – 1000 V 2 RFFE Supply Voltage V IO -0.5 – 2.7 V – RFFE Supply Voltage Levels V SCLK, V SDATA -0.7 – V IO + 0.7 (max. 2.7) V – Ambient temperature range 1 All voltages refer to GND-Nodes unless otherwise noted 2 Human Body Model ANSI/ESDA/JEDEC JS-001-2014 (R = 1.5 kΩ, C = 100 pF). Attention: Stresses above the max. values listed here may cause permanent damage to the device. Maximum ratings are absolute ratings; exceeding only one of these values may cause irreversible damage to the integrated circuit. Exposure to conditions at or below absolute maximum rating but above the specified maximum operation conditions may affect device reliability and life time. Functionality of the device might not be given under these conditions. Data Sheet 2 Revision 3.0 2018-04-23 BGAV1A10 Low Noise Amplifier with Gain Control RF Characteristics - Band 42 2 DC Characteristics Table 3: DC Characteristics at T A = 25 ◦C Parameter 1 Symbol Supply Voltage V DD Supply Current IDD Values Unit Note / Test Condition Min. Typ. Max. 1.7 1.8 1.9 V – 3.0 5.0 7.0 mA G0-G3 – 0.07 0.15 mA G4 VIO 1.65 1.8 1.95 V – VIH 0.7 * VIO – VIO V – VIL 0 – 0.3 * VIO V – RFFE output high voltage VOH 0.8 * VIO – VIO V – 3 RFFE output low voltage VOL 0 – 0.2 * VIO V – RFFE control input capacitance CCtrl – – 2 pF – RFFE supply current IVIO – 3 – µA Idle State RFFE supply voltage RFFE input high voltage 2 RFFE input low voltage2 3 1 Based on the application described in Chapter 6 2 SCLK and SDATA 3 SDATA 3 RF Characteristics - Band 42 Table 4: RF Characteristics in ON Mode at T A = 25 ◦C, V DD = 1.8 V, IVDD = 5.0 mA, f = 3.4– 3.6 GHz Parameter Insertion power gain f = 3500 MHz Noise figure f = 3500 MHz Symbol 1/|S21 |2 NF Values Unit Note / Test Condition Min. Typ. Max. 16.0 18.0 20.0 dB G0 13.3 15.3 17.3 dB G1 6.9 8.9 10.9 dB G2 -2.7 -0.7 1.3 dB G3 -4.7 -2.7 -0.7 dB G3 in Bias0 mode -5.4 -3.9 -2.4 dB G4 – 1.3 1.8 dB G0 – 1.4 1.9 dB G1 – 1.5 2.0 dB G2 – 10.1 11.1 dB G3 – 3.9 5.4 dB G4 Continued on next page Data Sheet 3 Revision 3.0 2018-04-23 BGAV1A10 Low Noise Amplifier with Gain Control RF Characteristics - Band 42 Table 4: RF Characteristics – Continued from previous page Parameter Input Return Loss f = 3500 MHz Output Return Loss f = 3500 MHz Reverse Isolation f = 3500 MHz Symbol RLin RLout 1/|S12 | Inband input 1dB-compression point IP1dB f = 3500 MHz Inband input 3rd -order intercept point1 IIP3 Phase discontinuity between all 2 Values Unit Note / Test Condition – – dB dB G0 G1 13 – dB G2 9 – dB G3 3 6 – dB G4 10 20 – dB G0 10 20 – dB G1 10 25 – dB G2 10 18 – dB G3 4 8 – dB G4 26 31 – dB G0 29 34 – dB G1 21 26 – dB G2 27 32 – dB G3 2.4 3.9 – dB G4 -17 -13 – dBm G0 -17 -13 – dBm G1 -10 -6 – dBm G2 -1 +3 – dBm G3 -8 -3 – dBm G0 -8 -3 – dBm G1 -4 +1 – dBm G2 +4 +9 – dBm G3 27 +32 – dBm G4 -6 – 6 ◦ Part to part variation after com- Min. Typ. Max. 9 9 13 13 9 6 Gain Mode combinations pensation in Base Band with f = 3500 MHz constant value Stability k >1 – – MIPI to RF time tINT – 1.5 2 µs Power Up Settling Time tBC – 10 25 µs 1 Input power = −30 dBm for each tone for modes G0-G3 / −15 dBm for mode G4, f Data Sheet 4 f = 20 MHz - 10 GHz 50 % last SCLK falling edge to 90 % ON, see Fig. 2 After power down mode 1 = 3500 MHz, f 2 = f 1 + 1 MHz Revision 3.0 2018-04-23 BGAV1A10 Low Noise Amplifier with Gain Control RF Characteristics - Band 43 4 RF Characteristics - Band 43 Table 5: RF Characteristics in ON Mode at T A = 25 ◦C, V DD = 1.8 V, IVDD = 5.0 mA, f = 3.6– 3.8 GHz Parameter Insertion power gain f = 3700 MHz Noise figure f = 3700 MHz Input Return Loss f = 3700 MHz Output Return Loss f = 3700 MHz Reverse Isolation f = 3700 MHz Symbol 1/|S21 |2 NF RLin RLout 1/|S12 | 2 Values Unit Note / Test Condition Min. Typ. Max. 15.6 17.6 19.6 dB G0 12.8 14.8 16.8 dB G1 6.4 8.4 10.4 dB G2 -2.9 -0.9 1.1 dB G3 -4.9 -2.9 -0.9 dB G3 in Bias0 mode -5.4 -3.9 -2.4 dB G4 – 1.4 1.9 dB G0 – 1.5 2.0 dB G1 – 1.6 2.1 dB G2 – – 10.2 3.9 11.2 5.4 dB dB G3 G4 6 9 – dB G0 6 9 – dB G1 7 10 – dB G2 6 9 – dB G3 4 7 – dB G4 10 14 – dB G0 10 18 – dB G1 10 20 – dB G2 10 20 – dB G3 8 11 – dB G4 27 32 – dB G0 29 22 34 27 – – dB dB G1 G2 28 33 – dB G3 2.4 3.9 – dB G4 Continued on next page Data Sheet 5 Revision 3.0 2018-04-23 BGAV1A10 Low Noise Amplifier with Gain Control RF Characteristics - Band 43 Table 5: RF Characteristics – Continued from previous page Parameter Symbol Inband input 1dB-compression point IP1dB f = 3700 MHz Inband input 3rd -order intercept point1 IIP3 Phase discontinuity between all Values Unit Note / Test Condition – – dBm dBm G0 G1 -5 – dBm G2 +3 – dBm G3 -10 -5 – dBm G0 -10 -5 – dBm G1 -5 0 – dBm G2 +2 +7 – dBm G3 25 +30 – dBm G4 -6 – 6 ◦ Part to part variation after com- Min. Typ. Max. -18 -18 -14 -14 -9 -1 Gain Mode combinations pensation in Base Band with f = 3700 MHz constant value Stability k >1 – – MIPI to RF time tINT – 1.5 2 µs Power Up Settling Time tBC – 10 25 µs 1 Input power = −30 dBm for each tone for modes G0-G3 / −15 dBm for mode G4, f Data Sheet 6 f = 20 MHz - 10 GHz 50 % last SCLK falling edge to 90 % ON, see Fig. 2 After power down mode 1 = 3700 MHz, f 2 = f 1 + 1 MHz Revision 3.0 2018-04-23 BGAV1A10 Low Noise Amplifier with Gain Control RF Characteristics - Band 43 SDATA TINT SCLK 90% RF Signal Figure 1: MIPI to RF Time VBAT VIO SDATA SCLK a) TPUP VBAT VIO SDATA SCLK b) TPUP Figure 2: Power-Up Settling Time Definition: a) when the device is already in Active Mode. b) when changing from Low Power Mode to Active Mode. After Power-Up of VIO the device is set to Low Power Mode. An additional MIPI instruction is necessary to set the device to Active Mode. This case is covered by b). Data Sheet 7 Revision 3.0 2018-04-23 BGAV1A10 Low Noise Amplifier with Gain Control MIPI RFFE Specification 5 MIPI RFFE Specification All sequences are implemented according to the ’MIPI Alliance Specification for RF Front-End Control Interface’ document version 2.0 - 25. September 2014. Table 6: MIPI Features Feature Supported MIPI RFFE 2.0 standard Yes Register 0 write command sequence Yes Register read and write command sequence Yes Extended register read and write command se- Yes Comment quence Support for standard frequency range operations Yes Up to 26 MHz for read and write Yes Up to 52 MHz for write for SCLK Support for extended frequency range operations for SCLK Half speed read Yes Full speed read Yes Full speed write Yes Programmable Group SID Yes Programmable USID Yes Support for three registers write and extended write sequences Trigger functionality Yes Broadcast / GSID write to PM TRIG register Yes Reset Yes Status / error sum register Yes Extended product ID register Yes Revision ID register Yes Group SID register Yes USID_Sel pin Yes Via VIO, PM TRIG or software register External pin for changing USID: USID 12=00 → 1000, USID 12=10 → 1001, USID 12=01 → 1010, USID 12=11 → 1011 USID selection via SDATA / SCLK swap feature No Table 7: Startup Behavior Feature State Comment Power status Low power Lower power mode after start-up Trigger function Enabled Enabled after start-up. Programmable via behavior control register Data Sheet 8 Revision 3.0 2018-04-23 BGAV1A10 Low Noise Amplifier with Gain Control MIPI RFFE Specification Table 8: Register Mapping, Table I Register Address Register Name Data Bits Function Description 0x00 REGISTER_0 7:0 MODE_CTRL LNA control 0x1C PM_TRIG PWR_MODE(1), Operation Mode 0: Normal operation (ACTIVE) 7 Default Broadcast_ID Support Trigger Support R/W 00000000 No Yes R/W 1 Yes No R/W 1: Low Power Mode (LOW POWER) 6 PWR_MODE(0), State Bit Vector 0: No action (ACTIVE) 0 1: Powered Reset (STARTUP to ACTIVE to LOW POWER) 5 TRIGGER_MASK_2 0: Data masked (held in shadow REG) 0 No 1: Data not masked (ready for transfer to active REG) 4 TRIGGER_MASK_1 0: Data masked (held in shadow REG) 0 1: Data not masked (ready for transfer to active REG) 3 TRIGGER_MASK_0 0: Data masked (held in shadow REG) 0 1: Data not masked (ready for transfer to active REG) 2 TRIGGER_2 0: No action (data held in shadow REG) 0 Yes 1: Data transferred to active REG 1 TRIGGER_1 0: No action (data held in shadow REG) 0 1: Data transferred to active REG 0 TRIGGER_0 0: No action (data held in shadow REG) 0 1: Data transferred to active REG 0x1D PRODUCT_ID 7:0 PRODUCT_ID This is a read-only register. However, during the programming of the USID a write command sequence is performed on this register, even though the write does not change its value. 00001101 No No R 0x1E MAN_ID 7:0 MANUFACTURER_ID [7:0] This is a read-only register. However, during the programming of the USID, a write command sequence is performed on this register, even though the write does not change its value. 00011010 No No R 0x1F MAN_USID 7:6 RESERVED Reserved for future use 00 No No R 5:4 MANUFACTURER_ID [9:8] These bits are read-only. However, during the programming of the USID, a write command sequence is performed on this register even though the write does not change its value. 01 3:0 USID[3:0] Programmable USID. Performing a write to this register using the described programming sequences will program the USID in devices supporting this feature. These bits store the USID of the device. See Tab. 6 No No R/W Data Sheet 9 Revision 3.0 2018-04-23 BGAV1A10 Low Noise Amplifier with Gain Control MIPI RFFE Specification Table 9: Register Mapping, Table II Register Address Register Name Data Bits Function 0x20 EXT_PRODUCT_ID 7:0 EXT_PRODUCT_ID 0x21 REV_ID 7:4 MAIN_REVISION 3:0 SUB_REVISION 0x22 GSID 7:4 GSID0[3:0] Primary Group Slave ID. 0000 3:0 RESERVED Reserved for secondary Group Slave ID. 0000 7 UDR_RST Reset all configurable non-RFFE Reserved registers to default values. 0: Normal operation 1: Software reset 0 6:0 RESERVED Reserved for future use 0000000 7 RESERVED Reserved for future use 0 6 COMMAND_FRAME_PARITY_ERR Command Sequence received with parity error − discard command. 0 0x23 UDR_RST 0x24 ERR_SUM 0x78 Data Sheet DFT Description Default Broadcast_ID Support Trigger Support 00000000 No No R 0001 No No R/W No No R/W No No R/W No No R – – – 0000 5 COMMAND_LENGTH_ERR Command length error. 0 4 ADDRESS_FRAME_PARITY_ERR Address frame with parity error. 0 3 DATA_FRAME_PARITY_ERR Data frame with parity error. 0 2 READ_UNUSED_REG Read command to an invalid address. 0 1 WRITE_UNUSED_REG Write command to an invalid address. 0 0 BID_GID_ERR Read command with a BROADCAST_ID or GROUP_ID. 0 DESIGN_FOR_TEST Do not use. – 7:0 R/W 10 Revision 3.0 2018-04-23 BGAV1A10 Low Noise Amplifier with Gain Control MIPI RFFE Specification Table 10: Gain Modes of Operation (Truth Table, Register_0) REGISTER_0 Bits State Mode D6 D5 D4 D3 D2 D1 D0 1 Gain G0 1 0 0 1 x x x 2 Gain G1 1 0 1 1 x x x 3 Gain G2 1 1 0 1 x x x 4 Gain G3 1 1 1 0 x x x 5 Gain G4 (Bypass) 0 1 1 1 x x x Table 11: Bias settings (Truth Table, Register_0) REGISTER_0 Bits State Mode D6 D5 D4 D3 D2 D1 D0 9 Bias0 (3.0 mA) 1 x x x 0 0 0 10 Bias1 (3.5 mA) 1 x x x 0 0 1 11 Bias2 (4.0 mA) 1 x x x 0 1 0 12 Bias3 (4.5 mA) 1 x x x 0 1 1 13 Bias4 (5.0 mA)1 1 x x x 1 0 0 14 Bias5 (5.5 mA) 1 x x x 1 0 1 15 Bias6 (6.0 mA) 1 x x x 1 1 0 16 Bias7 (6.5 mA) 1 x x x 1 1 1 1 Target bias mode for Gain modes G0-G3 Data Sheet 11 Revision 3.0 2018-04-23 BGAV1A10 Low Noise Amplifier with Gain Control Application Information 6 Application Information GND SDATA 8 7 6 5 RFin 3 4 VIO 2 USID1 1 VDD 10 SCLK RFout 9 GND USID2 Pin Configuration and Function Figure 3: BGAV1A10 Pin Configuration (top view) Table 12: Pin Definition and Function Pin No. Name Function 1 VDD Power supply 2 RFin RF input port 3 USID1 USID select pin 1 4 VIO MIPI RFFE supply 5 SCLK MIPI RFFE clock 6 SDATA MIPI RFFE data 7 GND Ground 8 RFout RF output port 9 USID2 USID select pin 2 GND Ground 10 1 Leave unconnected if not used (do NOT connect to GND) Data Sheet 12 Revision 3.0 2018-04-23 BGAV1A10 Low Noise Amplifier with Gain Control Application Information Application Board Configuration S S RFin L1 VDD VIO RFout LNA MIPI-RFFE Control Interface C1 C2 SDATA SCLK USID1 USID2 (optional) Figure 4: BGAV1A10 Application Schematic Table 13: Bill of Materials Table Name Value Package Manufacturer Function C1 10 nF 0201 Various RF bypass1 C2 (optional) 10 nF 0201 Various RF bypass1 L1 1.5nH 0201 muRata LQP type Input matching2 N1 BGAV1A10 ATSLP-10-1 Infineon Variable gainstep LNA 1 RF bypass recommended to mitigate power supply noise. 2 The matching elements must be optimized with reference to the frequency band of interest. Data Sheet 13 Revision 3.0 2018-04-23 BGAV1A10 Low Noise Amplifier with Gain Control Package Information 7 Package Information 0.4 0.1 A 5 4 6 3 7 2 8 1 10 B INDEX MARKING (LASERED) 0.6±0.05 0.2±0.05 10x 0.2±0.05 10x 9 0.1 B 1.1±0.05 1.5±0.05 A 0.4 ALL DIMENSIONS ARE IN UNITS MM THE DRAWING IS IN COMPLIANCE WITH ISO 128 & PROJECTION METHOD 1 [ ] Figure 5: ATSLP-10-1 Package Outline (top, side and bottom views) TYPE CODE DATE CODE (YW) PIN1 MARKING (LASERED) Figure 6: Marking Specification (top view) Product Name Marking Package BGAV1A10 V1 ATSLP-10-1 Data Sheet 14 Revision 3.0 2018-04-23 BGAV1A10 Low Noise Amplifier with Gain Control Package Information Table 14: Year date code marking - digit "Y" Year "Y" Year "Y" Year "Y" 2000 0 2010 0 2020 0 2001 1 2011 1 2021 1 2002 2 2012 2 2022 2 2003 2004 3 4 2013 2014 3 4 2023 2024 3 4 2005 5 2015 5 2025 5 2006 6 2016 6 2026 6 2007 7 2017 7 2027 7 2008 8 2018 8 2028 8 2009 9 2019 9 2029 9 Table 15: Week date code marking - digit "W" Data Sheet Week "W" Week "W" Week "W" Week "W" Week "W" 1 A 12 N 23 4 34 h 45 v 2 B 13 P 24 5 35 j 46 x 3 C 14 Q 25 6 36 k 47 y 4 D 15 R 26 7 37 l 48 z 5 E 16 S 27 a 38 n 49 8 6 F 17 T 28 b 39 p 50 9 7 G 18 U 29 c 40 q 51 2 8 H 19 V 30 d 41 r 52 3 9 J 20 W 31 e 42 s 53 M 10 11 K L 21 22 Y Z 32 33 f g 43 44 t u 15 Revision 3.0 2018-04-23 BGAV1A10 Low Noise Amplifier with Gain Control Package Information 0.25 Optional solder mask dam 0.4 0.25 0.2 0.2 0.4 0.25 0.25 0.4 0.4 copper solder mask stencil apertures ALL DIMENSIONS ARE IN UNITS MM Figure 7: Footprint Recommendation 4 PIN 1 INDEX MARKING 0.75 1.7 8 4 1.3 ALL DIMENSIONS ARE IN UNITS MM THE DRAWING IS IN COMPLIANCE WITH ISO 128 & PROJECTION METHOD 1 [ ] Figure 8: Carrier Tape Data Sheet 16 Revision 3.0 2018-04-23 Revision History Page or Item Subjects (major changes since previous revision) Revision 3.0, 2018-04-23 all "Preliminary" removed 2 Maximum current into pin VDD updated 2 Maximum RF input power updated 2 Maximum total power dissipation updated 14 Package outline drawing updated 14 Marking specification drawing updated 15 Date code marking tables added 16 Footprint recommendation drawing added 16 Carrier tape drawing added 17 Trademarks updated Other Trademarks All referenced product or service names and trademarks are the property of their respective owners. Edition 2018-04-23 Published by Infineon Technologies AG 81726 Munich, Germany c 2018 Infineon Technologies AG. All Rights Reserved. Do you have a question about any aspect of this document? Email: erratum@infineon.com Document reference Doc_Number IMPORTANT NOTICE The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics ("Beschaffenheitsgarantie"). With respect to any examples, hints or any typical values stated herein and/or any information regarding the application of the product, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. In addition, any information given in this document is subject to customer’s compliance with its obligations stated in this document and any applicable legal requirements, norms and standards concerning customer’s products and any use of the product of Infineon Technologies in customer’s applications. The data contained in this document is exclusively intended for technically trained staff. It is the responsibility of customer’s technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). WARNINGS Due to technical requirements products may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies office. Except as otherwise explicitly approved by Infineon Technologies in a written document signed by authorized representatives of Infineon Technologies, Infineon Technologies products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury.